arduino diy needle seder with steep motors

-

hello,

i need arduino code seeder.
i have 2 steep motors, need move first motor 70% left ,pause 1 second ,move right vertical botton , pause 1 second, in same time second motor move 1 step left , wait 3 second, when first motor in 70% position  vacum pump need suck seed , when 1 mottor vertical 0 position vacum pump need blow seed ... im not rly english speker sry thet.. put video can see i'm thing .https://www.youtube.com/watch?v=su87nvbk5am  have 2  l298 module stepp motor , 12/5/3,3 v power suply.

tnx answer

you need post code have tried , explain , want different.

if want write code please ask in gigs , collaborations section of forum , prepared pay.

these links may help
stepper motor basics
simple stepper code

the demo several things @ time illustrates use of millis() manage timing.

planning , implementing program


...r


Arduino Forum > Using Arduino > Motors, Mechanics, and Power (Moderator: fabioc84) > arduino diy needle seder with steep motors


arduino

Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino Uno not uploading

-
hi guys, so, have arduino uno r3 (not wired thing) when try upload sketch (even empty sketch) first takes long in "uploading..." comes error: arduino: 1.8.0 (windows 10), board: "arduino/genuino uno" sketch uses 444 bytes (1%) of program storage space. maximum 32256 bytes. global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes local variables. maximum 2048 bytes. avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more