Skip to main content

Thread: Using laptop as internet source for PC (just a little smudgeon of help please!)

-

let me catch speed.

have:
have wireless router.
have laptop can connect wireless router.
have pc wired laptop.
have edited sysctl.conf , uncommented net.ipv4.ip_forward=1 (on laptop)
have done "sysctl -a"

need:
need have pc connect internet using wireless laptop.

reasons beyond control cannot move pc router or modem easier wired access. after have internet , have run few programs can undo of , access wirelessly pc.

please advise,
thank you.

edit: progress of professional. unfortunately helping me through aim , little difficult , still unsuccessful making progress.

laptop's 'auto eth0'
ipv4 settings:
method: manual
address: 10.1.1.1
netmask: 255.255.255.0
gateway: 0.0.0.0

pc's 'auto eth0'
ipv4 settings:
method: manual
address: 10.1.1.2
netmask: 255.255.255.0
gateway: 10.1.1.1

2 computers can ping eachother.
laptop can ping router.
laptop can ping pc.
pc can ping laptop , router.
pc can ping 4.2.2.1.
pc cannot open webpages.

install dnsmasq

laptop can ping pc
pc can't ping anything.

going bed. 3:15 am. please help.

bump


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Networking & Wireless [ubuntu] Using laptop as internet source for PC (just a little smudgeon of help please!)


Ubuntu

Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino Uno not uploading

-
hi guys, so, have arduino uno r3 (not wired thing) when try upload sketch (even empty sketch) first takes long in "uploading..." comes error: arduino: 1.8.0 (windows 10), board: "arduino/genuino uno" sketch uses 444 bytes (1%) of program storage space. maximum 32256 bytes. global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes local variables. maximum 2048 bytes. avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more