P2P communication 2 ESP8266 programming by arduino IDE

-

hi guys,

i new esp8266 , need run quick test if module of use me.
the esp8266 using digikey partnumber 1568-1235-nd (most common module)

what test is:
- 1 esp6288 push button on gpio2
- second esp8266 external led on gpio2
- both powered ftdi-board , usb cable pc
- direct communication between these 2 esp8266 wifi (without using arduino, raspberry or so)

- when pushbutton pushed, led on other esp8266 should light up
(if possible output (print)  pc-screen ftdi connection)

is 1 aware of these codes , willing supply me code 'server' , 'client' unit? program modules using arduino ide

it great help. many in advance

frans 
the netherlands


this same question have.

did figure out? i'd hate buy 2 esp8266's if can't.


Arduino Forum > Development > Other Software Development > P2P communication 2 ESP8266 programming by arduino IDE


arduino

Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino Uno not uploading

-
hi guys, so, have arduino uno r3 (not wired thing) when try upload sketch (even empty sketch) first takes long in "uploading..." comes error: arduino: 1.8.0 (windows 10), board: "arduino/genuino uno" sketch uses 444 bytes (1%) of program storage space. maximum 32256 bytes. global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes local variables. maximum 2048 bytes. avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more