Skip to main content

Thread: All programs hang when starting, then crash

-

i have tried 3 fresh installs of ubuntu 9.10 using ext4 formatted hard disk. experienced issue 1 hard disk, tried fresh install on another, same issue. when ubuntu boots can termimal start, no other programs, when try open folder, flashes momentarily, disappears. each program says "starting {program name}" in bar @ bottom of screen, hangs disappears. want start using ubuntu, odd worked fine live cd, not when installed hard disk.

have tried "sudo apt-get install -f" , first tells me "segmentation faultsts... 22%", if try command again, console outputs "segmentation faulty tree... 50%"

ideas?

are able boot ubuntu graphical desktop? , program can open terminal? correct? or not graphical desktop @ all? sounds bit strange.

first, rule out bad install cd source of problem, boot cd used install ubuntu , run option "check disc defects". if cd passes, good. report results of this.
if cd good, try running programs terminal , post error messages get. example, run firefox, type firefox in terminal , hit enter. run totem video player, type totem. report errors get.
should provide enough info diagnose this.

, welcome ubuntu forums!


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support Installation & Upgrades [ubuntu] All programs hang when starting, then crash


Ubuntu

Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino Uno not uploading

-
hi guys, so, have arduino uno r3 (not wired thing) when try upload sketch (even empty sketch) first takes long in "uploading..." comes error: arduino: 1.8.0 (windows 10), board: "arduino/genuino uno" sketch uses 444 bytes (1%) of program storage space. maximum 32256 bytes. global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes local variables. maximum 2048 bytes. avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more