Skip to main content

Thread: Wireless setup issues

-

for strange reason have tried sucker work doesnt want too. here ask pros think issue may be. have had 9.04 running on server before , had , working , fine... decided mess around , install different operating system on test things out.. when went linux re installing it... weirdest thing... after configure in /etc/network/interfaces type in iwconfig see if connected... sure enough shows connected wifi wpa using tkip , wext driver. shows there no information being transferred.. , sure enough when try , apt wont let me anything... let me both iwlist , interfaces show how have setup.. dunno... maybe doing wrong.

first step did sudo vim /etc/network/interfaces create this.

code:
auto lo  iface lo inet loopback    auto ra0  iface ra0 inet static  address <my ip>  gateway <my gateway addy>	  dns-nameservers <i have 2 if them.. matter use?>  netmask 255.255.255.248 <this same subnet right?>  wpa-driver wext  wpa-ssid <level3>  wpa-ap-scan 1  wpa-proto wpa  wpa-pairwise tkip  wpa-group tkip  wpa-key-mgmt wpa-psk  wpa-psk <my_hex_key>
now go , type in sudo /etc/init.d/networking restart

afterwards type in iwconfig , information.

code:
lo     no wireless extensions    eth0   no wireless extensions    ra0    rt2860 wireless essid:"level3"         mode:auto frequency=2.412 ghz         link quality=100/100 signal level:87 dbm noise level:-143 dbm         rx invalid nwid:0 rx invalid crypt:0 rx invalid frag:0         tx excessive retries:0 invalid misc:0 missed beacon:0


here have ideas....???? know can going using gui... dont want 1 takes resources want. anyways appreciated!!!



Forum The Ubuntu Forum Community Ubuntu Specialised Support Ubuntu Servers, Cloud and Juju Server Platforms [ubuntu] Wireless setup issues


Ubuntu

Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino Uno not uploading

-
hi guys, so, have arduino uno r3 (not wired thing) when try upload sketch (even empty sketch) first takes long in "uploading..." comes error: arduino: 1.8.0 (windows 10), board: "arduino/genuino uno" sketch uses 444 bytes (1%) of program storage space. maximum 32256 bytes. global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes local variables. maximum 2048 bytes. avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more