Skip to main content

Thread: Help, my Ktorrent isn't working...

-

i'm not familiar technical aspects of programs. anyway have installed ktorrent kde windows installer , worked nicely. have followed directions. have downloaded few .torrents. last time using it, there 2 .torrents on download, added third , during pre-allocation of memory space ktorrent stopped working. tried open ktorrent again did not work anymore. tried restart laptop, remove few files documents accommodate 3gig required last .torrent file entered, same result, ktorrent failed run. made re-installation of version of ktorrent , same result, did not work. deleted last file (from download files) corresponding third .torrent tried preallocate memory with, , noticed every time attempt run ktorrent, file reappears. there's file or laptop, maybe, not remove last .torrent queued, , ktorrent keeps on trying process fails , dialogue box instead appears saying: "ktorrent.exe has stopped working..a problem cause program stop working correctly. windows close program , notify if solution available."

how can remove last .torrent entered, or how can make ktorrent run again?

thanks.

try:

code:
sudo apt-get purge ktorrent sudo apt-get install ktorrent
edit: sorry, realised on windows. have no idea how in case, sorry.


Forum The Ubuntu Forum Community Ubuntu Official Flavours Support New to Ubuntu [ubuntu] Help, my Ktorrent isn't working...


Ubuntu

Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino Uno not uploading

-
hi guys, so, have arduino uno r3 (not wired thing) when try upload sketch (even empty sketch) first takes long in "uploading..." comes error: arduino: 1.8.0 (windows 10), board: "arduino/genuino uno" sketch uses 444 bytes (1%) of program storage space. maximum 32256 bytes. global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes local variables. maximum 2048 bytes. avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more