Ukendt fejl ved VM 1.0.13a - Joomla! Forum - community, help and support

-

hej,

jeg oplever et problem med vm, som jeg aldrig er stødt på før og kan ikke lige løse det.

jeg installere vm 1.0.13a på joomla 1.0.13

hver gang jeg opretter en varegruppe/kategori og vare får jeg denne fejl, og bliver efterfølgende nødt til @ logge ind backend igen.

"warning: session_start(): cannot send session cookie - headers sent (output started @ /var/www/rayon/sjaelsro.dk/htdocs/includes/joomla.php:4145) in /var/www/rayon/sjaelsro.dk/htdocs/includes/joomla.php on line 800

warning: session_start(): cannot send session cache limiter - headers sent (output started @ /var/www/rayon/sjaelsro.dk/htdocs/includes/joomla.php:4145) in /var/www/rayon/sjaelsro.dk/htdocs/includes/joomla.php on line 800"


nogen der kan hjælpe? andre der har oplevet dette?

jeg er ikke sindsygt sikker, men jeg mener @ der med 1.0.13 kom et session problem..

der ligger en patch et eller andet sted du vil sikkert kunne finde den på virtuemarts forum, eller også ved @ søge efter tilsvarrende session problemer forumet.

desværre kommer der ikke en 1.0.14 hvor fejlene fra 1.0.13 er rettet, da 1.0.x kun opdateres hvis der er sikkerhedsmæssige problemer.
jeg ved ikke om der findes en opdateret pakke, et sted da det jo faktisk er den version der er stable, så det er lidt surt @ man skal søge efter patch og selv patche sin 1.0.13.





Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino Uno not uploading

-
hi guys, so, have arduino uno r3 (not wired thing) when try upload sketch (even empty sketch) first takes long in "uploading..." comes error: arduino: 1.8.0 (windows 10), board: "arduino/genuino uno" sketch uses 444 bytes (1%) of program storage space. maximum 32256 bytes. global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes local variables. maximum 2048 bytes. avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more