Linke til article / Static content - Joomla! Forum - community, help and support

-

hejsa.
er det ikke muligt med en standard-installation muligt @ linke direkte til andre artikler (static content gamle dage).
problemet er  :) :jeg har en side, hvor jeg gerne vil linke til en anden side. men når jeg klikker på link-ikonet, er det ikke muligt @ vælge andre artikler.
kan det virkelig passe, @ jeg skal ind backend og finde det id og en url @ kunne lave et simpelt link til en anden artikel?
med sef slået til bliver det jo noget tungvendt. slet ikke @ snakke om, hvordan jeg forklarer det til andre redaktørere...

burde det ikke være muligt fra den "insert link" mulighed @ vælge en artikel? er der noget jeg overser?
eller skal jeg installere en ny editor?

<-- mod notes jessdk: tråden er nu sat til solved -->

det er ikke muligt med de indbyggede wysiwyg editors, jeg ved @ det er muligt med jce men den er ikke kommet til 1.5 endnu, den virker måske med legacy slået til, men jeg har ikke prøvet det.  jeg plejer bare @ linke til den fulde url ikke super smart men det virker og det burde ikke være indviklet en bruger @ gøre.





Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino Uno not uploading

-
hi guys, so, have arduino uno r3 (not wired thing) when try upload sketch (even empty sketch) first takes long in "uploading..." comes error: arduino: 1.8.0 (windows 10), board: "arduino/genuino uno" sketch uses 444 bytes (1%) of program storage space. maximum 32256 bytes. global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes local variables. maximum 2048 bytes. avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x9f avrdude: stk500_recv(): programmer not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x9f avrdude...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more