Advice on converting analog Hi8mm tapes to digital

-

hi,

 

i looking advice on converting hi8mm analog video tapes digital. not tapes still prefer obtain quality transfer. may editing on few of them in pre , maintain ability edit them in future.

 

at present, i've bought roxio easyvhstodvd usb converter states can capture in dv-avi format doesn't appear able so. results far @ capturing have been finicky @ best i'm still working on wary because format captured not dv-avi.

 

i've read several people here suggesting using ads pyro a/d firewire converter. better, less troublesome route go? , other tips have in doing a/d conversion?

 

thanks,

paul

yes ads pyro best way go... either pyro or canopus range of dv converters... ie advc110 or advc300. advc300 best of bunch has timebase corrector can eliminate dropped frames on older tapes.

 

your tape captured 1 clip, if burning straight dvd not problem. if want editing may want capture using scene detect option. split video clips (virtual clips within pe7, ie tape still capyured 1 video) , place them in media bin can drag them timeline. not sure how pe7 scene detect option works... have had mixed results in past similar programs. end splitting myself manually.



More discussions in Premiere Elements


adobe

Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino DUE ADC to DAC Piezo 30 Khz-100Khz

-
i working on project providing echo response ultrasonic sensors. piezo facing opposite ultrasonic sensor,with foam material in between damp ultrasonic signal reflecting sensor. event based,read piezo signal[(+) --> a0,(-) --> gnd on arduino due] , after delay(5 ms) drive same piezo through dac0 [(+)---> dac0,(-)--> gnd) so ultrasonic sensor receives signal (30 khz-100 khz) after delay,thereby calculating distance after time of flight of 5 ms. int in_adc0,out_dac0;  //variables adc,dac values (adc0, dac0) void setup() {   //adc configuration   adc->adc_mr |= 0x80;   // dac in free running mode.   adc->adc_cr=2;         // starts adc conversion.   adc->adc_cher=0x80;  // enable adc channels 0     analogreadresolution(12);  analogwriteresolution(12);   //dac configuration   analogwrite(dac0,0);  // enables dac0   serial.begin(9600); }   void loop() { ...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more