CF4.5 uses 100% CPU and hangs

-

hello,

 

according coldfusion forums problem not new 1 still want
to post hope kind of answer.

 

i'm running following system:

 

cf 4.5 enterprise server

siteminder 6.0

iis 5.0
ms sqlserver 2005

 

both cf , database server win2000 sp4.

 

about every 1 hours cf server uses 100% cpu , on is
impossible log application. site still available though.
after restarting cf service works fine until.....

 

i not know triggers suspect has with
siteminder , logging onto application.

 

the site has go live on monday can imagine pressure get
this fixed before weekend.

 

greetings,

 

jilani

unfortunately don't think you'll stock answer upgrade!. 4.5 old version - started out on over decade or ago afaik.  not many people running , doesn't have active support more.

 

it's asking support microsoft wfw 3.11 or dos.

 

sorry



More discussions in ColdFusion Server Administration


adobe

Comments

Post a Comment

Popular posts from this blog

Flip address is out of range arduino uno r3

-
hello  guy, trying flash firmware on arduino uno rev3 atmega 16u2 using atmel flip. whenever try , import .hex file program, throws error " address out of range ." have looked around online , haven't found solution. , info helpful. here hex file : https://github.com/nicohood/hoodloader2/blob/master/avr/bootloaders/hexfiles/hoodloader2_0_5_uno_atmega16u2.hex its using arduino uno hid Arduino Forum > Using Arduino > Installation & Troubleshooting > Flip address is out of range arduino uno r3 arduino
Read more

Arduino DUE ADC to DAC Piezo 30 Khz-100Khz

-
i working on project providing echo response ultrasonic sensors. piezo facing opposite ultrasonic sensor,with foam material in between damp ultrasonic signal reflecting sensor. event based,read piezo signal[(+) --> a0,(-) --> gnd on arduino due] , after delay(5 ms) drive same piezo through dac0 [(+)---> dac0,(-)--> gnd) so ultrasonic sensor receives signal (30 khz-100 khz) after delay,thereby calculating distance after time of flight of 5 ms. int in_adc0,out_dac0;  //variables adc,dac values (adc0, dac0) void setup() {   //adc configuration   adc->adc_mr |= 0x80;   // dac in free running mode.   adc->adc_cr=2;         // starts adc conversion.   adc->adc_cher=0x80;  // enable adc channels 0     analogreadresolution(12);  analogwriteresolution(12);   //dac configuration   analogwrite(dac0,0);  // enables dac0   serial.begin(9600); }   void loop() { ...
Read more

Indesign and MathType fonts

-
i having trouble getting indesign recognize mathtype fonts.  have been told move mathtype fonts on 2 indesign font folder.  copied mt-extra font file mathtype folder , pasted indesign font folder.  nothing changed.  indesign still gives me blank box after copy mt-extra font mathtype -->illustrator-->indesign.   guess need instructions on how transfer of fonts done correctly.  i'v looked @ install fonts manual indesign, not clear me on how it.  need utility fontexplorer this, or there other way.  what's weird working fine until had reinstall osx , reinstall cs3, font trouble started.  need toggle "activate-reactivate' adobe cs3 , don't know how close 20 max on this, worried that.  (i suspect because of note on forum might necessary).  thoughts appreciated. i'm using windows, advice may worth nothing...   1) shouldn't have deactivate id recognize fonts. 2) design science gives fonts away in type 1 , truetype flavors....
Read more